So you want to start a motorcycle. If the machine is in good condition, this should not be difficult. Read on for a basic tutorial on how to start a motorcycle!
StepsMethod 1Method 1 of 3:Getting your Bearings
1Determine whether you have a carburetor-based or fuel-injected motorcycle. Many motorcycles, especially older or less expensive models, do not have modern fuel injection systems. If you aren’t sure, you can tell by looking for a choke control. It is normally located on the left handlebar, above the horn. Carbureted motorcycles have a choke, but fuel-injected bikes do not.X
2Sit on your motorcycle seat when starting it. This will put you in full control of anything that happens once it’s started. If you are starting the motorcycle unmounted for some reason, make sure that you shift your bike into neutral (located between 1st and 2nd gear) before you fire the engine. You don’t want the bike to take off without you!
3Make sure that the motorcycle is in working condition. You should have plenty of gas and a well-charged battery. It is important to keep the motorcycle properly serviced, particularly in damp or cold conditions. Fit new spark plugs, or, if not worn, clean and gap the old ones. Check the ignition timing, and adjust if necessary; if fitted, have the ignition points replaced. A carburetor service and clean is also a great idea.Replace the spark plug leads if they look old, worn, or frayed. Use only manufacturer-recommended spark plugs and plug leads – look for the reference in your motorcycle’s handbook.4Check the oil level. Before starting any engine, make sure it is lubricated by checking the oil level. If there is no oil, or the oil level is too low, do not start the engine. Otherwise it will heat up, then will break down.
5Check the battery. Put in the key and turn the key clockwise until the lights turn on. If the lights does not turn on, that usually means the battery is dead and you need to recharge it or install a new one.Method 2Method 2 of 3:Starting a Carburated Motorcycle
1Look for the “choke” lever or cut-off switch. For cold starting, there is usually a choke lever or “cut-off switch” on the handlebar. On some bikes, there may be a choke lever mounted on the carburetor. Operating this will provide the necessary rich fuel mixture when the motorcycle is “cold” – when it hasn’t been used for more than a few hours. The dirtier the carburetor, or the colder the engine is, the more the choke will need to be engaged.XYou don’t need to use the choke lever when starting a motorcycle “hot.” If the motorcycle has been running and the engine is already hot, you won’t need as much power to get it going. Just use a small amount of throttle and the engine should fire.XMany bikes have a cut-off switch on the kickstand, so make sure that the kickstand is up as well. Having the bike in neutral will disable the kickstand shutoff.2Open the choke lever. Make sure that the cut-off switch is “on.” You will need to leave the handlebar throttle twist-grip closed while operating the starter motor or kick-start lever. Otherwise, the engine will flood, making starting difficult or impossible. Remember – the choke lever is usually not necessary if the bike has already been running in the past few hours.X3Turn your ignition to the “on” position. Your dash lights should “light up” when it’s in this position. Also if your bike is in neutral as suggested, then you should notice a green light indicating that you are in neutral.4Start the engine. Squeeze and hold your clutch lever down (located on the left) and push the start button (located on the right). You should hear the blissful sound of your motorcycle cranking up.5Close the choke and open the throttle. Shortly after the engine fires, close the choke lever progressively and open the throttle slightly as the engine warms. As you ride, you may still need some choke for a short distance – but close the choke lever as soon as possible to achieve smooth running. Do not over-rev the motorcycle when it is warming up.Method 3Method 3 of 3:Starting a Fuel-Injected Motorcycle1Put the motorcycle into neutral. You can almost always find this between first and second gear.X
2Don’t worry about the choke lever. For electronically fuel-injected motorcycles, the engine management system will automatically look after fueling needs whether the engine is hot or cold. There is no choke lever on these motorcycles. Use a small amount of throttle when starting either hot or cold.3Pull the clutch in toward the handlebar. It’s usually on the the left-hand side. Many riders choose to also pull in the front brake (on the right handlebar) at the same time.4Press and hold in the start button. This is usually located on the right handlebar, near the bottom of where the hand will naturally rest.5Try using the throttle. If the motorcycle does not catch and start, try using the throttle while pressing the start button. Make sure to keep the clutch held all of the way in while doing this.
